您好,欢迎您来访济南天锐升降机械有限公司! 公司主营:液压升降机、液压登车桥、液压升降平台、液压升降货梯等。

济南天锐升降机械有限公司

液压升降平台
丰富的升降机设备生产经验
为您提供用心的升降机全套解决方案
分类导航CLASSIFIED NAVIGATION
联系天锐机械 / Contact us
联系天锐机械

济南天锐升降机械有限公司

客户统一咨询热线

188-5411-2626

联系电话:0531-84250097

公司地址:山东省济南市济阳区济阳街道工业园15-4号

当前位置:  >  新闻中心

济南液压升降机保持平衡状态

文章来源:www.trsjjx.com   发布时间:2015-5-17 9:07:52   浏览次数:

返回:新闻动态

济南液压升降机http://www.trsjjx.com/是用来载人或者载货的重要作业工具,为了安全系数,济南液压升降机平衡是很重要的参数,国家规定济南液压升降机的摇摆度是控制在千分之五左右的,济南液压升降机产生相应的电流起到调节油缸的作用。
Jinan hydraulic lift is an important work tool for manned or cargo, and for the safety factor, Jinan hydraulic lift balance is a very important parameter, the swing state of Jinan hydraulic lift is controlled at about five thousandths of Jinan hydraulic lift generate corresponding current play a regulatory role in the fuel tank.

当济南液压升降机运行失去平衡的时候,济南液压升降机处在非平衡的作业状态,济南液压升降机中的调平油缸的就会产生伸缩动作,使平台恢复到水平状态,所以我们不用担心济南液压升降机的平衡度问题,升降机厂家在设计的时候都是把不稳定因素考虑到进去的。
When Jinan hydraulic lifts run out of balance, Jinan hydraulic lifts in the non-equilibrium state of the job, Jinan hydraulic lifts in leveling cylinders will produce telescopic action, so that the platform back to the horizontal state,so we do not worry about Jinan hydraulic lifts the balance of the issue, elevator manufacturers in the design of all the uncertainties taken into account into the.
 
济南液压升降机http://www.trsjjx.com/焊接结构的脆性破坏常起源于应力集中处,而焊缝、热影响区、熔合线和应变时效区也正处在应力集中的部位,因而在结构设计时要注意控制应力水平,应严格避免焊缝密集和采用十字焊缝,使相邻焊缝叉开相隔一定距离.接管、支座、人梯等附件应尽量避免焊在容器结构的主焊缝上或者焊在结构的高应力部位,当构 件上不同厚的结构度进行对接时,应尽可能采用圆滑过渡。总之,在设计中不应采用任何易造成应力集中的结构。
Jinan hydraulic lift brittle fracture of welded structures often originated in the stress concentration, and weld heat-affected zone, weld lines and strain aging zone is also in the stress concentration area, which in the structural design should pay attention to control the stress level, should strictly avoid dense and with cross seam weld, the weld deviates from the adjacent spaced. takeover, stand, ladder and other accessories should be avoided on the main seam weld or solder container structure in the structure of high stress location, when the structure of the different thickness of the docking member, should be adopted smooth transition. In short, should not be used in the design of any structure could easily lead to stress concentration.